Each individual component is designed to work with the other to ensure quality and reliability.when you just replaced a cartridge in your Brother MFC-7340 and the printer is still giving you a message Toner Life End. Each Brother laser printer is designed to work at pre-set temperatures that are matched exactly to each of our individual toner formulations. Brother strongly recommends that customers use only genuine Brother drum units and toner cartridges.Check What Color of Cartridge Needs Replacement Brother Printer Says No Toner after Replacing Toner How to Replace Brother Printer Toner Cartridge You are Using a Non-Brother Ink Cartridge Why is My Brother Printer Not Detecting Ink How to Override “Toner Low” on Brother Printer Ensure the Toner Cartridge is A New One
Brother Printer Says Replace Toner Install And ReinstallUse a clean, soft and dry cloth to properly but gently clean the metals.Step 4: Put the toner back into the drum unit assembly. Then lift the toner and take it out.Step 3: On the drum unit’s right side, you will find two metals that look like staples. Place the drum unit on a disposable cloth or paper because the toner can spill at any point of the repair.Step 2: Push the green locking tab on the drum unit’s left side. How to Fix Brother Printer No Toner ErrorStep 1: Open your printer’s front cover then take out the drum unit. So if your Brother printer does not detect toner, you need to uninstall and reinstall the drum unit assembly and toner cartridge to rectify the problem.So check the printer’s screen for which toner color needs replacement. Check What Color of Cartridge Needs ReplacementThe “No Toner” error may be for another cartridge color other than the one you replaced. How to Replace Brother Printer Toner CartridgeFollow these steps to replace your Brother printer toner cartridge…Step 1: Ensure your printer is on, and then open its front cover.Step 2: Remove the drum unit assembly from the printer and then place it on a piece of disposable cloth or paper.Step 3: Next, remove the toner cartridge by pushing down the green locking tab like in the previous solution.Step 4: Get the new toner and remove its protective cover.Step 5: There is a corona wire inside the drum unit, shift the green tab forth and back a few times to clean this corona wire.Step 6: Put the new toner into the drum unit assembly and then close the machine.The Genuine Brother Toner below is compatible with the following Brother printer models: DCP L2540DW, DCP L2520DW, HL L2300D, HL L2360DW, HL L2315DW, HL L2380DW, HL L2305W, HL L2320D, HL L2340DW, MFC L2685DW, MFC L2680W, MFC L2705DW, MFC L2720DW, MFC L2707DW, MFC L2700DW, MFC L2740DWClick Here Buy Yours Now! Brother Printer Says No Toner after Replacing Toner Try the following solutions if your Brother printer still says “No Toner” after replacing the toner cartridge… 1. Wiki tom anderson guitarsSo check and replace the toner cartridge if you have made this mistake. If you replace the drum unit instead of the toner cartridge, the “No Toner” message will keep showing. Check which Consumable You ReplacedYour Brother printer uses two different consumables: the drum unit and the toner cartridge. Gangnam style downloadEnsure the Toner Cartridge is A New OneIf you take out a toner cartridge from another printer or use an already used toner cartridge, your Brother printer’s toner status will not get reset. If you had not done this when replacing the cartridge then take out the drum unit assemble again and clean the corona wire. Clean the Corona WireCleaning the corona wires is very important when you replace your Brother printer’s toner. When you use an off-brand toner cartridge for your Brother printer, you put the life of the printer in danger.If you damage your printer while using an off-brand toner cartridge then you give up the right to your Brother limited warranty. Use a Genuine Brother Printer Toner CartridgeIf your Brother printer is not accepting a new toner then it’s most likely because the toner is not a genuine Brother printer toner cartridge. Afterward, put the toner back in place by doing steps 5-6 of the same solution. Brother MFC Printer SeriesStep 1: Open your printer’s front cover and press the “Clear/Back” key.Step 2: Press the “*” key and then press “0” twice.Step 3: Close the printer’s front cover and test run the printer. You have successfully overridden the “Toner Low” message on your Brother DCP printer series.Step 5: Close the printer’s front cover and test run the printer. “00” will now appear on the screen.Step 4: Press “OK”. Brother DCP Printer SeriesStep 1: Open your printer’s front cover and push the “Back/Clear” key.Step 2: “Replace Drum” will appear on the printer’s LCD screen, press “Start”.Step 3: Simultaneously press the down and up keys. How to Override “Toner Low” on Brother PrinterDo the following to override “Toner Low” on your Brother printer… i. In this case, you can choose to override the message. Ensure to choose “Yes” with each ink cartridge installed.Step 6: Once you are done installing each cartridge ink, close the ink cover door and test run the printer. For instance, “Did you change yellow?”. Ensure you insert the cartridge from the arrow label on it.Step 5: As you install each ink cartridge, your printer will send a confirmatory message. Because, if it is not, it will be unable to detect the ink after installation.Step 4: Put each ink cartridge in place according to their colors.
0 Comments
Leave a Reply. |
AuthorManuel ArchivesCategories |